index
會員中心 | English | 簡體中文
logo
首頁 產品與标準 ASME B 18.6.3 (T25-I/T25-IA+T40) - 2013 十字槽大扁頭 AB ABR自攻螺釘

十字槽大扁頭 AB ABR自攻螺釘 ASME B 18.6.3 (T25-I/T25-IA+T40) - 2013

選擇規格尺寸 點擊↓

0#

1#

2#

3#

4#

5#

6#

7#

8#

10#

12#

1/4

5/16

3/8

7/16

1/2

ASME B 18.6.3 (T25-I/T25-IA+T40) - 2013 十字槽大扁頭 AB ABR自攻螺釘

尺寸單位: inch
美标ASME B18.6.3 (T25-I/T25-IA+T40) - 2013 十字槽大扁頭 AB ABR自攻螺釘
ASME B 18.6.3 (T25-I/T25-IA+T40) - 2013 十字槽大扁頭 AB ABR自攻螺釘
掃一掃分享
公差 最小破壞扭矩 牌号等級
螺紋尺寸
d
0# 1# 2# 3# 4# 5# 6# 7#
d 公稱
PP
槽号
M1 參考值
M2 參考值
P I 型 最大值
最小值
IA型 最大值
最小值
dk 最大值
最小值
k 最大值
最小值
R 最大值
L0 ④ 公稱
Y ④ 螺紋過渡長度(全螺紋) 最大值
b ④ 螺紋長度 (長螺釘) 最小值
0.0600 0.0730 0.0860 0.0990 0.1120 0.1250 0.1380 0.1510
48 42 32 28 24 20 20 19
0 0 1 1 1 1 2 2
0.056 0.064 0.097 0.103 0.105 0.121 0.151 0.158
0.055 0.063 0.091 0.098 0.101 0.117 0.141 0.148
0.030 0.038 0.052 0.059 0.062 0.078 0..073 0.080
0.012 0.020 0.034 0.042 0.044 0.060 0.048 0.055
0.030 0.038 0.049 0.056 0.059 0.075 0.065 0.072
0.014 0.022 0.033 0.040 0.043 0.059 0.047 0.054
0.131 0.164 0.194 0.226 0.257 0.289 0.321 0.352
0.119 0.149 0.180 0.211 0.241 0.272 0.303 0.333
0.037 0.045 0.053 0.061 0.069 0.078 0.086 0.094
0.029 0.037 0.044 0.051 0.059 0.066 0.074 0.081
0.087 0.107 0.129 0.151 0.169 0.191 0.211 0.231
7/16 9/16 5/8 3/4 13/16 15/16 1 1-1/8
0.021 0.024 0.031 0.036 0.042 0.050 0.050 0.053
0.360 0.440 0.520 0.590 0.670 0.750 0.830 0.910
螺紋尺寸
d
8# 10# 12# 1/4 5/16 3/8 7/16 1/2
d 公稱
PP
槽号
M1 參考值
M2 參考值
P I 型 最大值
最小值
IA型 最大值
最小值
dk 最大值
最小值
k 最大值
最小值
R 最大值
L0 ④ 公稱
Y ④ 螺紋過渡長度(全螺紋) 最大值
b ④ 螺紋長度 (長螺釘) 最小值
0.1640 0.1900 0.2160 0.2500 0.3125 0.3750 0.4375 0.5000
18 16 14 14 12 12 10 10
2 2 3 3 4 4 4 4
0.166 0.181 0.241 0.256 0.345 0.376 0.407 0.437
0.155 0.171 0.227 0.241 0.326 0.357 0.387 0.415
0.088 0.104 0.111 0.126 0.173 0.206 0.237 0.268
0.063 0.079 0.086 0.101 0.148 0.182 0.212 0.243
0.079 0.095 0.101 0.115 0.161 0.192 0.223 0.251
0.061 0.077 0.083 0.097 0.143 0.174 0.205 0.233
0.384 0.448 0.511 0.573 0.698 0.823 0.948 1.073
0.364 0.425 0.487 0.546 0.666 0.787 0.907 1.028
0.102 0.118 0.134 0.150 0.183 0.215 0.248 0.280
0.088 0.103 0.118 0.133 0.162 0.191 0.221 0.250
0.254 0.283 0.336 0.375 0.457 0.538 0.619 0.701
1-1/4 1-3/8 1-5/8 1-13/16 1-13/16 1-7/8 1-7/8 1-7/8
0.056 0.062 0.071 0.071 0.083 0.083 0.100 0.100
0.980 1.140 1.300 1.500 1.500 1.500 1.500 1.500
①,若以小數規定公稱直徑，應省略小數前和小數點後第四位的零。
②,螺釘末端釘尖上不允許因螺紋輾壓而形成的虛尖，允許略帶圓弧或圓鈍形末端。
③,小于等于8#的螺釘，螺紋牙頂平面寬度不應超過0.004in，大于8#的應不超過0.006in。
④,正常情況下，當螺釘長度小于等于其公稱長度L0時應采用全螺紋，過渡螺紋長度應小于等于Y；若螺釘長度大于其公稱長度L0可采用半牙型式，但其螺紋長度應不小于b。
替代列表
ASME B 18.6.3T25-I/T25-IA+T40 - 2013 ASME B 18.6.3H7B-I/H7B-IA+T1A - 2024

采用标準

工藝相關

ASME B 18.6.3 (T24) - 2013
開槽扁圓頭螺釘 [Table 24] (ASTM F837, F468)
ASME B 18.6.3 (T24+T40) - 2013
開槽扁圓頭 AB ABR自攻螺釘
ASME B 18.6.3 (T25-I/T25-IA) - 2013
十字槽大扁頭螺釘 I、IA型
ASME B 18.6.3 (T25-III) - 2013
四方槽大扁頭螺釘
ASME B 18.6.3 (T25-III+T40) - 2013
四方槽大扁頭 AB ABR自攻螺釘
ASME B 18.6.3 (T25-VI) - 2013
梅花槽大扁頭螺釘
ASME B 18.6.3 (T25-VI+T40) - 2013
梅花槽大扁頭 AB ABR自攻螺釘

引用參考

GB /T 1172 - 1999
黑色金屬硬度及強度換算值
GB /T 5267.1 - 2002
鍍鋅、鍍鎳、鍍镉、複合鍍等層鍍層鹽霧腐蝕的防護性能
GB /T 193 - 2003
普通螺紋（一般用途米制螺紋）- 直徑與螺距系列 (ISO 261: 1998, MOD)
GB /T 3106 - 2016
緊固件 - 螺栓、螺釘和螺柱 - 公稱長度和螺紋長度 (ISO 888:2012, MOD)
GB /T 3 - 1997
普通螺紋收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)
GB /T 5779.1 - 2000
緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 一般要求
GB /T 5779.3 - 2000
緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 特殊要求
GB /T 3103.1 - 2002
緊固件公差（螺栓、螺柱、螺釘和螺母）
GB /T 34632 - 2017
統一螺紋搓制和滾制前的毛坯直徑
GB /T 18685 - 2017
普通螺紋搓制和滾制前的毛坯直徑
GB /T 3105 - 2002
普通螺栓和螺釘 - 頭下圓角半徑
GB /T 5279.2 - 1997
沉頭螺釘 第2部分 十字槽插入深度
GB /T 197 - 2018
普通螺紋 公差
注：技術數據僅供參考，請以官方原件為準！
類似标準及供貨信息
1 十字槽盤頭自攻螺釘 [國标]
GB /T 845 - 2017		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
供應商(12)
2 十字槽盤頭自攻螺釘 [國标]
GB /T 845 - 1985		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
供應商(12)
3 十字槽盤頭自攻螺釘 [國标]
GB 845 - 1976		 十字槽盤頭自攻螺釘
Cross recessed pan head self-tapping screws
供應商(12)
4 十字槽盤頭帶介自攻釘 [德标]
DIN 968 - 2008		 十字槽盤頭帶介自攻釘
Cross Recessed Pan Head Tapping Screws With Collar
供應商(3)
5 十字槽盤頭凸緣（華司）自攻釘 [德标]
DIN 968 - 2002		 十字槽盤頭凸緣（華司）自攻釘
Cross Recessed Pan Head Tapping Screws With Collar
供應商(3)
6 十字槽圓頭帶介自攻釘 [德标]
DIN 968 - 1994		 十字槽圓頭帶介自攻釘
Cross Recessed Pan Head Tapping Screws With Collar
供應商(3)
7 十字槽盤頭自攻釘 [德标]
DIN 7981 - 1990		 十字槽盤頭自攻釘
Cross Recessed Pan Head Tapping Screws
供應商(3)
8 十字槽盤頭自攻螺釘 [國際]
ISO 7049 - 2011		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
供應商(1)
9 十字槽盤頭自攻螺釘 [國際]
ISO 7049 - 1983		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
供應商(1)
10 十字槽大扁頭自攻釘 - 螺紋型式：Class 1~Class 4【附表4】 [日标]
JIS B 1122 (AAT4) - 1996		 十字槽大扁頭自攻釘 - 螺紋型式：Class 1~Class 4【附表4】
Cross Recessed Truss Head Tapping Screws - threaded portion are of class 1 to 4 [Annex attached table 4]
供應商(4)
11 十字槽矮圓柱頭自攻釘 - 螺紋型式：Class 1~Class 4【附表5】 [日标]
JIS B 1122 (AAT5) - 1996		 十字槽矮圓柱頭自攻釘 - 螺紋型式：Class 1~Class 4【附表5】
Cross Recessed Cheese Head Tapping Screws - threaded portion are of class 1 to 4 [Annex attached table 5]
12 十字槽盤頭自攻釘 【表1】 [日标]
JIS B 1122 (AT1) - 1996		 十字槽盤頭自攻釘 【表1】
Cross Recessed Pan Head Tapping Screws [Table 1]
13 十字槽盤頭自攻釘 - 螺紋型式：Class 1~Class 4【附表1】 [日标]
JIS B 1122 (AAT1) - 1996		 十字槽盤頭自攻釘 - 螺紋型式：Class 1~Class 4【附表1】
Cross Recessed Pan Head Tapping Screws - threaded portion are of class 1 to 4 [Annex Attached Table 1]
14 十字槽圓頭自攻釘 - 螺紋型式：Class 1~Class 4【附表6】 [日标]
JIS B 1122 (AAT6) - 1996		 十字槽圓頭自攻釘 - 螺紋型式：Class 1~Class 4【附表6】
Cross Recessed Brazier Head Tapping Screws - threaded portion are of class 1 to 4 [Annex attached table 6]
15 十字槽盤頭自攻釘C型 [汽标代号]
Q 271		 十字槽盤頭自攻釘C型
Cross recessed pan head tapping screws - Type C
16 十字槽盤頭平尾自攻釘F型 [汽标代号]
Q 272		 十字槽盤頭平尾自攻釘F型
Cross recessed round head tapping screws - Type F
17 十字槽大半圓頭自攻釘 [汽标代号]
Q 273		 十字槽大半圓頭自攻釘
Cross recessed round head tapping screws
18 十字槽盤頭自攻釘 [美标]
ASME/ANSI B 18.6.3 - 2010		 十字槽盤頭自攻釘
Machine Screw and Tapping Screw Nuts (Inch Seires)
19 十字槽球面圓柱頭自攻釘 [美标]
ASME/ANSI B 18.6.3 - 2010		 十字槽球面圓柱頭自攻釘
Machine Screw and Tapping Screw Nuts (Inch Seires)
20 塑料用米制十字槽盤頭螺釘 [意大利]
UNI 10227 - 1993		 塑料用米制十字槽盤頭螺釘
Recessed raised cheese (fillister) thread forming screws for plastic materials (Metric series）
21 十字槽盤頭自攻釘 [意大利]
UNI 6954		 十字槽盤頭自攻釘
Cross Recessed Pan Head Tapping Screws
22 十字槽盤頭自攻螺釘 [法國]
NF E 25-658 - 1994		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
23 米字槽扁頭凸緣（華司）自攻釘 [Table 19] [英标]
BS 4174 - 1972		 米字槽扁頭凸緣（華司）自攻釘 [Table 19]
Corss Recessed Flange Head Self-Tapping Screws [Table 19]
24 米字槽盤頭自攻釘 [Table 17] [英标]
BS 4174 - 1972		 米字槽盤頭自攻釘 [Table 17]
Cross Recess Pan Head Self-Tapping Screws [Table 17]
25 米制十字槽盤頭自攻螺釘 [澳标]
AS /NZS 4406 - 1996		 米制十字槽盤頭自攻螺釘
ISO metric cross recessed pan head tapping screws
26 十字槽盤頭自攻釘 [原電子工業部]
SJ 2821 - 1987		 十字槽盤頭自攻釘
Cross recessed pan head self-tapping screws
27 十字槽扁圓頭自攻釘 [原電子工業部]
SJ 2823 - 1987		 十字槽扁圓頭自攻釘

28 十字槽大扁圓頭自攻釘（ST 2.2~ST 6.3） [原電子工業部]
SJ 2500 - 1984		 十字槽大扁圓頭自攻釘（ST 2.2~ST 6.3）

29 十字槽盤頭帶墊自攻釘 [原電子工業部]
SJ 2501 - 1984		 十字槽盤頭帶墊自攻釘
Cross recessed pan head tapping screws with collar
30 十字槽盤頭普通螺紋自攻螺釘 [原電子工業部]
SJ 2502 - 1984		 十字槽盤頭普通螺紋自攻螺釘

31 十字槽扁圓頭普通螺紋自攻螺釘 [原電子工業部]
SJ 2504 - 1984		 十字槽扁圓頭普通螺紋自攻螺釘
Cross recessed oblate head tapping screws with common screw-thread
32 十字槽大扁頭自攻釘（ST 2.5~ST 6） [原電子工業部]
SJ 2824 - 1984		 十字槽大扁頭自攻釘（ST 2.5~ST 6）

33 十字槽盤頭自攻螺釘 [台灣]
CNS 4305 - 2000		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
34 十字槽盤頭自攻螺釘 [韓标]
KS B 1032 - 2016 (R2021)		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
35 十字槽盤頭自攻螺釘 [韓标]
KS B 1032 - 2001		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
36 塑料用十字槽圓頭帶介自攻螺釘【DELTA PT 螺紋】 [企标]
YJT 4024 (WN 5411)		 塑料用十字槽圓頭帶介自攻螺釘【DELTA PT 螺紋】
Round Washer Head with Type H or Type Z Cross Recess Self-tapping Screw [DELTA PT Thread]
供應商(1)
37 十字槽圓頭帶介自攻螺釘 [企标]
YJT 4054 (WN1411C-1)		 十字槽圓頭帶介自攻螺釘
Cross Recessed Pan Head Tapping Screws With Collar
供應商(1)
38 十字槽圓頭帶介自攻螺釘 [企标]
YJT 4055 (WN1411C-2)		 十字槽圓頭帶介自攻螺釘
Cross Recessed Pan Head Tapping Screws With Collar
供應商(1)
39 十字槽盤頭自攻螺釘 [企标]
YJT 4056 (WN1412C-1)		 十字槽盤頭自攻螺釘
Cross recessed pan head Tapping screws
供應商(1)
40 十字槽盤頭自攻螺釘 [企标]
YJT 4057 (WN1412C-2)		 十字槽盤頭自攻螺釘
Cross recessed pan head Tapping screws
供應商(1)
41 十字槽盤頭自攻釘 [德标]
DIN EN ISO 7049 - 2011		 十字槽盤頭自攻釘
Cross-recessed Pan Head Tapping Screws
供應商(3)
42 十字槽大扁頭自攻釘 [汽标]
QC /T 602 - 1999		 十字槽大扁頭自攻釘
Cross Recessed Mushroom Head Tapping Screws
43 十字槽盤頭 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (H5B-I/H5C-IA+T1A) - 2024		 十字槽盤頭 AB ABR自攻螺釘
Type I Cross Recessed Pan Head Tapping Screws - Type AB and ABR
44 十字槽球面圓柱頭 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (H6B-I/H6B-IA+T1A) - 2024		 十字槽球面圓柱頭 AB ABR自攻螺釘
Cross recessed raised cheese head tapping screws - Type AB and ABR
45 十字槽大扁頭 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (H7B-I/H7B-IA+T1A) - 2024		 十字槽大扁頭 AB ABR自攻螺釘
Cross Recessed Mushroom Head Tapping Screws - Type AB and ABR
46 十字槽圓頭 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (H11B-I/H11B-IA+T1A) - 2024		 十字槽圓頭 AB ABR自攻螺釘
Cross Recessed Round Head Tapping Screws - Type AB and ABR
47 十字槽圓頭凸緣 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (H12B-I+T1A) - 2024		 十字槽圓頭凸緣 AB ABR自攻螺釘
Cross recessed round head Tapping Screws With Collar - Type AB and ABR
48 十字槽盤頭 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (T18-I/T19-IA+T40) - 2013		 十字槽盤頭 AB ABR自攻螺釘
Type I Cross Recessed Pan Head Tapping Screws - Type AB and ABR
49 十字槽球面圓柱頭 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (T22-I/T22-IA+T40) - 2013		 十字槽球面圓柱頭 AB ABR自攻螺釘
Cross recessed raised cheese head tapping screws - Type AB and ABR
50 十字槽圓頭 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (T36-I/T36-IA+T40) - 2013		 十字槽圓頭 AB ABR自攻螺釘
Cross Recessed Round Head Tapping Screws - Type AB and ABR
51 十字槽圓頭凸緣 AB ABR自攻螺釘 [美标]
ASME B 18.6.3 (T39-I+T40) - 2013		 十字槽圓頭凸緣 AB ABR自攻螺釘
Cross recessed round head Tapping Screws With Collar - Type AB and ABR
52 米制米字槽盤頭自攻螺釘 [Table 18] [美标]
ASME B 18.6.5M (T18) - 2000 (R2010)		 米制米字槽盤頭自攻螺釘 [Table 18]
Metric Type IA Cross-Recessed Pan Head Tapping Screws [Table 18]
53 米制十字槽盤頭自攻螺釘 [Table 17] [美标]
ASME B 18.6.5M (T17) - 2000 (R2010)		 米制十字槽盤頭自攻螺釘 [Table 17]
Metric cross recessed pan head tapping screws [Table 17]
54 I型十字槽盤頭自攻螺釘 B,BP型 [Table 32] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽盤頭自攻螺釘 B,BP型 [Table 32]
Type I Cross Recessed Pan Head Tapping Screws - Type B and BP Thread Forming [Table 32]
55 I型十字槽盤頭自攻螺釘 C型 [Table 32] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽盤頭自攻螺釘 C型 [Table 32]
Type I Cross Recessed Pan Head Tapping Screws - Type C Thread Forming [Table 32]
56 I型十字槽盤頭自攻螺釘 AB型 [Table 32] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽盤頭自攻螺釘 AB型 [Table 32]
Type I Cross Recessed Pan Head Tapping Screws - Type AB Thread Forming [Table 32]
57 I型十字槽盤頭自攻螺釘 A型 [Table 32] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽盤頭自攻螺釘 A型 [Table 32]
Type I Cross Recessed Pan Head Tapping Screws - Type A Thread Forming [Table 32]
58 IA型米字槽盤頭自攻螺釘 B,BP型 [Table 33] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽盤頭自攻螺釘 B,BP型 [Table 33]
Type IA Cross Recessed Pan Head Tapping Screws - Type B and BP Thread Forming [Table 33]
59 IA型米字槽盤頭自攻螺釘 C型(統一螺紋) [Table 33] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽盤頭自攻螺釘 C型(統一螺紋) [Table 33]
Type IA Cross Recessed Pan Head Tapping Screws - Type C Thread Forming [Table 33]
60 IA型米字槽盤頭自攻螺釘 AB型 [Table 33] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽盤頭自攻螺釘 AB型 [Table 33]
Type IA Cross Recessed Pan Head Tapping Screws - Type AB Thread Forming [Table 33]
61 IA型米字槽盤頭自攻螺釘 A型 [Table 33] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽盤頭自攻螺釘 A型 [Table 33]
Type IA Cross Recessed Pan Head Tapping Screws - Type A Thread Forming [Table 33]
62 II型十字槽盤頭自攻螺釘 B,BP型 [Table 34] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽盤頭自攻螺釘 B,BP型 [Table 34]
Type II Cross Recessed Pan Head Tapping Screws - Type B and BP Thread Forming [Table 34]
63 II型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table 34] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table 34]
Type II Cross Recessed Pan Head Tapping Screws - Type C Thread Forming [Table 34]
64 II型十字槽盤頭自攻螺釘 AB型 [Table 34] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽盤頭自攻螺釘 AB型 [Table 34]
Type II Cross Recessed Pan Head Tapping Screws - Type AB Thread Forming [Table 34]
65 II型十字槽盤頭自攻螺釘 A型 [Table 34] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽盤頭自攻螺釘 A型 [Table 34]
Type II Cross Recessed Pan Head Tapping Screws - Type A Thread Forming [Table 34]
66 I型十字槽圓柱頭自攻螺釘 B,BP型 [Table 36] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽圓柱頭自攻螺釘 B,BP型 [Table 36]
Type I Cross Recessed Fillister Head Tapping Screws - Type B and BP Thread Forming [Table 36]
67 I型十字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 36] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 36]
Type I Cross Recessed Fillister Head Tapping Screws - Type C Thread Forming [Table 36]
68 I型十字槽圓柱頭自攻螺釘 AB型 [Table 36] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽圓柱頭自攻螺釘 AB型 [Table 36]
Type I Cross Recessed Fillister Head Tapping Screws - Type AB Thread Forming [Table 36]
69 I型十字槽圓柱頭自攻螺釘 A型 [Table 36] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽圓柱頭自攻螺釘 A型 [Table 36]
Type I Cross Recessed Fillister Head Tapping Screws - Type A Thread Forming [Table 36]
70 IA型米字槽圓柱頭自攻螺釘 B,BP型 [Table 37] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽圓柱頭自攻螺釘 B,BP型 [Table 37]
Type IA Cross Recessed Fillister Head Tapping Screws - Type B and BP Thread Forming [Table 37]
71 IA型米字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 37] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 37]
Type IA Cross Recessed Fillister Head Tapping Screws - Type C Thread Forming [Table 37]
72 IA型米字槽圓柱頭自攻螺釘 AB型 [Table 37] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽圓柱頭自攻螺釘 AB型 [Table 37]
Type IA Cross Recessed Fillister Head Tapping Screws - Type AB Thread Forming [Table 37]
73 IA型米字槽圓柱頭自攻螺釘 A型 [Table 37] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽圓柱頭自攻螺釘 A型 [Table 37]
Type IA Cross Recessed Fillister Head Tapping Screws - Type A Thread Forming [Table 37]
74 II型十字槽圓柱頭自攻螺釘 B,BP型 [Table 38] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽圓柱頭自攻螺釘 B,BP型 [Table 38]
Type II Cross Recessed Fillister Head Tapping Screws - Type B and BP Thread Forming [Table 38]
75 II型十字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 38] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 38]
Type II Cross Recessed Fillister Head Tapping Screws - Type C Thread Forming [Table 38]
76 II型十字槽圓柱頭自攻螺釘 AB型 [Table 38] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽圓柱頭自攻螺釘 AB型 [Table 38]
Type II Cross Recessed Fillister Head Tapping Screws - Type AB Thread Forming [Table 38]
77 II型十字槽圓柱頭自攻螺釘 A型 [Table 38] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽圓柱頭自攻螺釘 A型 [Table 38]
Type II Cross Recessed Fillister Head Tapping Screws - Type A Thread Forming [Table 38]
78 I型十字槽大扁頭自攻螺釘 B,BP型 [Table F2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽大扁頭自攻螺釘 B,BP型 [Table F2]
Type I Cross Recessed Truss Head Tapping Screws - Type B and BP Thread Forming [Table F2]
79 I型十字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F2]
Type I Cross Recessed Truss Head Tapping Screws - Type C Thread Forming [Table F2]
80 I型十字槽大扁頭自攻螺釘 AB型 [Table F2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽大扁頭自攻螺釘 AB型 [Table F2]
Type I Cross Recessed Truss Head Tapping Screws - Type AB Thread Forming [Table F2]
81 I型十字槽大扁頭自攻螺釘 A型 [Table F2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽大扁頭自攻螺釘 A型 [Table F2]
Type I Cross Recessed Truss Head Tapping Screws - Type A Thread Forming [Table F2]
82 IA型米字槽大扁頭自攻螺釘 B,BP型 [Table F3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽大扁頭自攻螺釘 B,BP型 [Table F3]
Type IA Cross Recessed Truss Head Tapping Screws - Type B and BP Thread Forming [Table F3]
83 IA型米字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F3]
Type IA Cross Recessed Truss Head Tapping Screws - Type C Thread Forming [Table F3]
84 IA型米字槽大扁頭自攻螺釘 AB型 [Table F3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽大扁頭自攻螺釘 AB型 [Table F3]
Type IA Cross Recessed Truss Head Tapping Screws - Type AB Thread Forming [Table F3]
85 IA型米字槽大扁頭自攻螺釘 A型 [Table F3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽大扁頭自攻螺釘 A型 [Table F3]
Type IA Cross Recessed Truss Head Tapping Screws - Type A Thread Forming [Table F3]
86 II型十字槽大扁頭自攻螺釘 B,BP型 [Table F4] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽大扁頭自攻螺釘 B,BP型 [Table F4]
Type II Cross Recessed Truss Head Tapping Screws - Type B and BP Thread Forming [Table F4]
87 II型十字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F4] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F4]
Type II Cross Recessed Truss Head Tapping Screws - Type C Thread Forming [Table F4]
88 II型十字槽大扁頭自攻螺釘 AB型 [Table F4] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽大扁頭自攻螺釘 AB型 [Table F4]
Type II Cross Recessed Truss Head Tapping Screws - Type AB Thread Forming [Table F4]
89 II型十字槽大扁頭自攻螺釘 A型 [Table F4] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽大扁頭自攻螺釘 A型 [Table F4]
Type II Cross Recessed Truss Head Tapping Screws - Type A Thread Forming [Table F4]
90 I型十字槽盤頭自攻螺釘 B,BP型 [Table G2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽盤頭自攻螺釘 B,BP型 [Table G2]
Type I Cross Recessed Round Head Tapping Screws - Type B and BP Thread Forming [Table G2]
91 I型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table G2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table G2]
Type I Cross Recessed Round Head Tapping Screws - Type C Thread Forming [Table G2]
92 I型十字槽盤頭自攻螺釘 A型 [Table G2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽盤頭自攻螺釘 A型 [Table G2]
Type I Cross Recessed Round Head Tapping Screws - Type A Thread Forming [Table G2]
93 II型十字槽盤頭自攻螺釘 B,BP型 [Table G3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽盤頭自攻螺釘 B,BP型 [Table G3]
Type II Cross Recessed Round Head Tapping Screws - Type B and BP Thread Forming [Table G3]
94 II型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table G3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table G3]
Type II Cross Recessed Round Head Tapping Screws - Type C Thread Forming [Table G3]
95 II型十字槽盤頭自攻螺釘 A型 [Table G3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽盤頭自攻螺釘 A型 [Table G3]
Type II Cross Recessed Round Head Tapping Screws - Type A Thread Forming [Table G3]
96 十字槽大扁頭自攻螺釘 [深圳緊固件行業協會标準]
T/SZJGJ 001 (B) - 2024		 十字槽大扁頭自攻螺釘
Cross Recessed Mushroom Head Tapping Screws
97 十字槽盤頭自攻螺釘 [深圳緊固件行業協會标準]
T/SZJGJ 001 (D) - 2024		 十字槽盤頭自攻螺釘
Cross Recessed Pan Head Tapping Screws
© 易緊通 服務熱線：4006-164580（免長途費）