index
會員中心 | English | 簡體中文
logo
首頁 產品與标準 ASME B 18.6.3 (T1) - 2013 82°開槽沉頭機械螺釘 [Table 1] (ASTM F837 / F468)

82°開槽沉頭機械螺釘 [Table 1] (ASTM F837 / F468) ASME B 18.6.3 (T1) - 2013

選擇規格尺寸 點擊↓

0000#

000#

00#

0#

1#

2#

3#

4#

5#

6#

8#

10#

12#

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

ASME B 18.6.3 (T1) - 2013 82°開槽沉頭機械螺釘 [Table 1] (ASTM F837 / F468)

尺寸單位: inch
美标ASME B18.6.3 (T1) - 2013 ASME18.6.3 18 82°開槽沉頭機械螺釘 [Table 1] (ASTM F837 / F468)
模型下載
ASME B 18.6.3 (T1) - 2013 82°開槽沉頭機械螺釘 [Table 1] (ASTM F837 / F468)
掃一掃分享
單重計算 公差 美制螺紋極限尺寸 米/英制螺紋對照 螺紋直徑與受力截面積 最小破壞扭矩 牌号等級
螺紋尺寸
d
0000# 000# 00# 0# 1# 2# 3# 4# 5# 6# 8#
d 公稱
PP
L ② 詳見備注
dk 最大值
最小值
k 參考值
n 最大值
最小值
t 最大值
最小值
α 最大值
最小值
0.0210 0.0340 0.0470 0.0600 0.0730 0.0860 0.0990 0.1120 0.1250 0.1380 0.1640
- - - - 64.0 56.0 48.0 40.0 40.0 32.0 32.0
- - - 1/8 1/8 1/8 1/8 3/16 3/16 3/16 1/4
0.040 0.060 0.087 0.112 0.137 0.162 0.187 0.212 0.237 0.262 0.312
0.035 0.055 0.080 0.096 0.120 0.144 0.167 0.191 0.215 0.238 0.285
0.011 0.016 0.028 0.035 0.043 0.051 0.059 0.067 0.075 0.083 0.100
0.008 0.011 0.017 0.023 0.026 0.031 0.035 0.039 0.043 0.048 0.054
0.004 0.007 0.010 0.016 0.019 0.023 0.027 0.031 0.035 0.039 0.045
0.007 0.009 0.014 0.015 0.019 0.023 0.027 0.030 0.034 0.038 0.045
0.003 0.005 0.009 0.010 0.012 0.015 0.017 0.020 0.022 0.024 0.029
82° 82° 82° 82° 82° 82° 82° 82° 82° 82° 82°
80° 80° 80° 80° 80° 80° 80° 80° 80° 80° 80°
螺紋尺寸
d
10# 12# 1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4
d 公稱
PP
L ② 詳見備注
dk 最大值
最小值
k 參考值
n 最大值
最小值
t 最大值
最小值
α 最大值
最小值
0.1900 0.2160 0.2500 0.3125 0.3750 0.4375 0.5000 0.5625 0.6250 0.7500
24.0 24.0 20.0 18.0 16.0 14.0 13.0 12.0 11.0 10.0
5/16 3/8 7/16 1/2 9/16 5/8 3/4 - - -
0.362 0.412 0.477 0.597 0.717 0.760 0.815 0.932 1.050 1.285
0.333 0.380 0.442 0.556 0.670 0.715 0.765 0.878 0.990 1.215
0.116 0.132 0.153 0.191 0.230 0.223 0.223 0.260 0.298 0.372
0.060 0.067 0.075 0.084 0.094 0.094 0.106 0.118 0.133 0.149
0.050 0.056 0.064 0.072 0.081 0.081 0.091 0.102 0.116 0.131
0.053 0.060 0.070 0.088 0.106 0.103 0.103 0.120 0.137 0.171
0.034 0.039 0.046 0.058 0.070 0.066 0.065 0.077 0.088 0.111
82° 82° 82° 82° 82° 82° 82° 82° 82° 82°
80° 80° 80° 80° 80° 80° 80° 80° 80° 80°
①,頭部邊緣為倒圓或平的。
②,小于等于表中長度的螺釘，為清根沉頭型。
③,“光杆直徑”應不小于2A級螺紋最小中徑，并不大于公稱（基本）螺紋大徑。
④,機械螺釘的螺紋長度：

1）螺紋規格≤5#: 公稱長度≤3倍公稱直徑的應為滿扣產品，頭下螺紋肩距≤1倍螺距。 公稱長度＞3倍公稱直徑到 1-1/8 in 的，允許頭下肩距最大不超過2倍螺距。 若無其他規定，長螺釘的最小螺紋長度為1 in 。

2）螺紋規格≥6#: 公稱長度≤3倍公稱直徑的應為滿扣產品，頭下螺紋肩距≤1倍螺距。 公稱長度＞3倍公稱直徑到 2 in 的，允許頭下螺紋肩距最大不超過2倍螺距。 若無其他規定，長螺釘的最小螺紋長度為 1.5 in 。
替代列表
ASME/ANSI B 18.6.3 - 2010 ASME B 18.6.3T1 - 2013 ASME B 18.6.3H1A - 2024

采用标準

工藝相關

ASME B 18.6.3 (T9) - 2013
開槽82°沉頭清根機械螺釘 [ Table 9 ] (ASTM F837 / F468)
ASME B 18.6.3 (T1+T40) - 2013
82°開槽沉頭自攻螺釘 AB(ABR)型 [Table 1+Table 40]
ASME B 18.6.3 (T2-VI) - 2013
梅花槽82° 沉頭螺釘
ASME B 18.6.3 (T2-I/T2-IA+T40) - 2013
十字槽82度沉頭AB ABR自攻螺釘
ASME B 18.6.3 (T2-III+T40) - 2013
方槽82度沉頭AB ABR自攻螺釘
ASME B 18.6.3 (T2-VI+T40) - 2013
梅花槽82°沉頭 AB ABR自攻螺釘
ASME B 18.6.3 (T2-I/T2-IA) - 2013
82°十字槽沉頭螺釘 [Table 2] (ASTM F837, F468)
ASME B 18.6.3 (T2-III) - 2013
四方槽沉頭螺釘 [Table 2] (ASTM F837, F468)

引用标準：

1 82°沉頭螺釘的凹槽型式 【Table 2】 [美标]
ASME/ANSI B 18.6.3 (T2) - 2013		 82°沉頭螺釘的凹槽型式 【Table 2】
Recess Dimensions for Flat 82° Countersunk Head Screws
沉頭螺釘的凹槽型式

引用參考

GB /T 1172 - 1999
黑色金屬硬度及強度換算值
GB /T 5267.1 - 2002
鍍鋅、鍍鎳、鍍镉、複合鍍等層鍍層鹽霧腐蝕的防護性能
GB /T 193 - 2003
普通螺紋（一般用途米制螺紋）- 直徑與螺距系列 (ISO 261: 1998, MOD)
GB /T 3106 - 2016
緊固件 - 螺栓、螺釘和螺柱 - 公稱長度和螺紋長度 (ISO 888:2012, MOD)
GB /T 3 - 1997
普通螺紋收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)
GB /T 5779.1 - 2000
緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 一般要求
GB /T 5779.3 - 2000
緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 特殊要求
GB /T 3103.1 - 2002
緊固件公差（螺栓、螺柱、螺釘和螺母）
GB /T 34632 - 2017
統一螺紋搓制和滾制前的毛坯直徑
GB /T 18685 - 2017
普通螺紋搓制和滾制前的毛坯直徑
GB /T 3105 - 2002
普通螺栓和螺釘 - 頭下圓角半徑
GB /T 5279.2 - 1997
沉頭螺釘 第2部分 十字槽插入深度
GB /T 197 - 2018
普通螺紋 公差
注：技術數據僅供參考，請以官方原件為準！
類似标準及供貨信息
2 開槽沉頭螺釘 [國标]
GB /T 68 - 2016		 開槽沉頭螺釘
Slotted Countersunk Flat Head Screws
供應商(6)
3 開槽沉頭螺釘 [國标]
GB /T 68 - 2000		 開槽沉頭螺釘
Slotted Countersunk Head Screws (Commen Head Style)
供應商(6)
4 開槽沉頭螺釘 [國标]
GB 68 - 1985		 開槽沉頭螺釘
Slotted Countersunk Head Screws
供應商(6)
5 開槽沉頭不脫出螺釘 [國标]
GB 948 - 1988		 開槽沉頭不脫出螺釘
Slotted Countersunk Head Screws with Waisted Shank
6 米制開槽沉頭機械螺釘 Table 2 [美标]
IFI 513 - 1982		 米制開槽沉頭機械螺釘 Table 2
Metric Slotted Flat Countersunk Head Machine Screws
7 開槽沉頭螺釘 [德标]
DIN 963 - 1990		 開槽沉頭螺釘
Slotted Countersunk Head Screws
供應商(3)
8 鋼結構用帶六角螺母的開槽沉頭螺栓 [德标]
DIN 7969 - 2017		 鋼結構用帶六角螺母的開槽沉頭螺栓
Slotted countersunk head bolts with hexagon nut for steel structures
9 鋼結構用帶六角螺母的開槽沉頭螺栓 [德标]
DIN 7969 - 1989		 鋼結構用帶六角螺母的開槽沉頭螺栓
Slotted countersunk head screws for structural steel bolting for supply with or without nuts
10 開槽沉頭（平頭）螺釘 - 适用于精密機械；M0.4至M1.4 [德标]
DIN 8245 - 1972		 開槽沉頭（平頭）螺釘 - 适用于精密機械；M0.4至M1.4
Slotted Countersunk (Flat) Head Screws for Fine Mechanics; M 0.4 to M 1.4
11 開槽沉頭螺釘（通用頭型） - 產品等級A級 [國際]
ISO 2009 - 2011		 開槽沉頭螺釘（通用頭型） - 產品等級A級
Slotted Countersunk Flat Head Screws (Common Head Style) - Product Grade A
12 開槽沉頭螺釘（通用頭型） - 產品等級A級 [國際]
ISO 2009 - 1994		 開槽沉頭螺釘（通用頭型） - 產品等級A級
Slotted Countersunk Flat Head Screws (common Head Style) - Product Grade A
13 精密機械用開槽沉頭螺釘 [日标]
JIS B 1116 - 2009		 精密機械用開槽沉頭螺釘
Slotting Countersunk Head Screws For Fine Mechanics
供應商(1)
14 開槽沉頭螺釘 表8 [日标]
JIS B 1101 (T8) - 2017		 開槽沉頭螺釘 表8
Slotted Countersunk Head Screws - Table 8
15 開槽沉頭螺釘 附表JA.4 [日标]
JIS B 1101 (JA4) - 2017		 開槽沉頭螺釘 附表JA.4
Slotted Countersunk Head Screws - Table JA.4
16 開槽沉頭螺釘 附表2 [Annex Attached Table 2] [日标]
JIS B 1101 (AAT2) - 1996		 開槽沉頭螺釘 附表2 [Annex Attached Table 2]
Slotted Countersunk Head Screws [Annex Attached Table 2]
17 開槽沉頭螺釘 表3 [Attached Table 3] [日标]
JIS B 1101 (AT3) - 1996		 開槽沉頭螺釘 表3 [Attached Table 3]
Slotted Countersunk Head Screws [Attached Table 3]
18 開槽沉頭螺栓 (精制) [Table 1-1] [日标]
JIS B 1179 (T1-1) - 1994		 開槽沉頭螺栓 (精制) [Table 1-1]
Slotted Flat Head Bolts, Fine Finished [Table 1-1]
19 開槽沉頭螺栓 (粗制）[Table 1-2] [日标]
JIS B 1179 (T1-2) - 1994		 開槽沉頭螺栓 (粗制）[Table 1-2]
Slotted Flat Head Bolts, Rough Finished [Table 1-2]
20 80°開槽沉頭螺釘Table1 [美标]
ASME/ANSI B 18.6.3 - 2010		 80°開槽沉頭螺釘Table1
80° Slotted flat countersunk head machine screws
21 100°開槽沉頭螺釘Table3 [美标]
ASME/ANSI B 18.6.3 - 2010		 100°開槽沉頭螺釘Table3
Slotted 100 deg flat countersunk head screws (machine screws only)
22 緊公差100°開槽沉頭螺釘Table5 [美标]
ASME/ANSI B 18.6.3 - 2010		 緊公差100°開槽沉頭螺釘Table5
Close Tolerance 100 Degree Slotted Countersunk Head Screws
23 80°開槽沉頭清根螺釘Table9 [美标]
ASME/ANSI B 18.6.3 - 2010		 80°開槽沉頭清根螺釘Table9
80° Slotted undercut 82-deg flat countersunk head machine screws
24 開槽沉頭螺釘 [Table 1] (A307, SAE J429, F468, F593) [美标]
ASME/ANSI B 18.6.2 - 1998 (R2010)		 開槽沉頭螺釘 [Table 1] (A307, SAE J429, F468, F593)
Slotted Flat Countersunk Head Cap Screws [Table 1] (A307, SAE J429, F468, F593)
25 米制開槽沉頭螺釘Table2 [美标]
ASME/ANSI B 18.6.7M - 1998		 米制開槽沉頭螺釘Table2
Metric soltted countersunk screws
26 開槽100°沉頭小螺釘 [Table 3] [美标]
ASME/ANSI B 18.11 - 1961 (R1983)		 開槽100°沉頭小螺釘 [Table 3]
Slotted 100°flat head miniature screws
27 開槽沉頭螺釘 [意大利]
UNI 6109		 開槽沉頭螺釘
Slotted countersunk flat head screws
28 開槽沉頭螺釘 [法國]
NF E 25-123 - 1994		 開槽沉頭螺釘
Slotted Countersunk Flat Head Screws - Product Grade A
29 鐵路車輛 沉頭側切口機械螺釘 [法國]
NF F 03-004 (F) - 1983		 鐵路車輛 沉頭側切口機械螺釘
Railway rolling stock Grade A Countersunk notched head machine
30 鐵路車輛 開槽沉頭螺釘/螺母 A級 符号FP [法國]
NF F 03-016 - 1983		 鐵路車輛 開槽沉頭螺釘/螺母 A級 符号FP
Railway rolling stock Grade A Slotted countersunk head screws nuts Symbol FP
31 開槽沉頭螺釘（短的）Table 6 [英标]
BS 1981 - 1991		 開槽沉頭螺釘（短的）Table 6
Slotted Truncated Countersunk Head Screws: Short Length
32 開槽沉頭螺釘Table4 [英标]
BS 1981 - 1991		 開槽沉頭螺釘Table4
Slotted Countersunk Flat Head Screws
33 開槽沉頭機械螺釘 [英标]
BS 4183 (T2) - 1967		 開槽沉頭機械螺釘
Slotted countersunk head machine screws. Metric series
34 英制開槽沉頭螺釘 - B.S.W. & B.S.F. 螺紋 [Table 2] [英标]
BS 450 - 1958		 英制開槽沉頭螺釘 - B.S.W. & B.S.F. 螺紋 [Table 2]
Slotted 90°Countersunk Head Screws with B.S.W. & B.S.F. Threads [Table 2]
35 米制開槽沉頭螺釘 [Table 1] [澳标]
AS /NZS 1427 - 1996		 米制開槽沉頭螺釘 [Table 1]
ISO metric slotted countersunk head screws [Table 1]
36 精密機械用開槽沉頭螺釘 [台灣]
CNS 9678 - 1982		 精密機械用開槽沉頭螺釘
Slotted Countersunk Screws For Fine Mechanics
37 開槽沉頭螺釘 [台灣]
CNS 4411 - 1981		 開槽沉頭螺釘
Slotted Countersunk Head Screws
38 開槽沉頭螺栓 [台灣]
CNS 4420 - 1981		 開槽沉頭螺栓
Slotted Countersunk Head Bolts
39 精密用開槽沉頭螺釘 M0.4～M1.4 [台灣]
CNS 4363 - 1980		 精密用開槽沉頭螺釘 M0.4～M1.4
Slotted Countersunk Head Screws For Fine Mechanics
40 開槽沉頭螺釘 A級和B級 [俄标]
GOST 17475 - 1980		 開槽沉頭螺釘 A級和B級
Countersunk head screws of accuracy classes A and B（Slotted）
41 開槽沉頭螺釘【Table 5】 [韓标]
KS B 1021 (T5) - 2012 (R2022)		 開槽沉頭螺釘【Table 5】
Slotted Countersunk Flat Head Screws【Table 5】
42 開槽沉頭螺釘(通用頭型) A級 [德标]
DIN EN ISO 2009 - 2011		 開槽沉頭螺釘(通用頭型) A級
Slotted Countersunk Flat Head Screws(Common Head Style)-Product Grade A
供應商(3)
43 光杆公差帶f9 100°沉頭螺栓 [軍标]
GJB 3371 (/61) - 1998		 光杆公差帶f9 100°沉頭螺栓
100° Countersunk Head Bolts，Shank Tolerance f9
44 100°開槽沉頭螺釘 [軍标]
GJB 3372 (/36~/44) - 1998		 100°開槽沉頭螺釘
Slotted 100 deg flat countersunk head screws
45 100°沉頭不脫出螺釘 [軍标]
GJB 3372 (/56) - 1998		 100°沉頭不脫出螺釘
Slotted 100 deg flat countersunk head screws, Waisted shank
46 開槽沉頭螺釘（通用頭型） - 產品等級A級 [印标]
IS 1365 - 2005		 開槽沉頭螺釘（通用頭型） - 產品等級A級
Slotted Countersunk Flat Head Screws (common Head Style) - Product Grade A
47 開槽100°沉頭小螺釘 [Table 3] (A276, B16, B151) [美标]
ANSI B 18.11 - 1961 (R2017)		 開槽100°沉頭小螺釘 [Table 3] (A276, B16, B151)
Slotted 100°Flat Head Miniature Screws [Table 3] (A276, B16, B151)
48 82°開槽沉頭機械螺釘 (ASTM F837/F468) [TABLE 2.2.1-1] [美标]
ASME B 18.6.3 (H1A) - 2024		 82°開槽沉頭機械螺釘 (ASTM F837/F468) [TABLE 2.2.1-1]
82° Slotted Flat Countersunk Head Machine Screws (ASTM F837/F468) [TABLE 2.2.1-1]
49 100°沉頭開槽機械螺釘 (ASTM F837/F468) [TABLE 2.2.1-3] [美标]
ASME B 18.6.3 (H1C) - 2024		 100°沉頭開槽機械螺釘 (ASTM F837/F468) [TABLE 2.2.1-3]
Slotted 100-deg Flat Countersunk Head Screws (ASTM F837/F468) [TABLE 2.2.1-3]
50 精密100°沉頭開槽機械螺釘 (ASTM F837/F468) [TABLE 2.2.1-5] [美标]
ASME B 18.6.3 (H1E) - 2024		 精密100°沉頭開槽機械螺釘 (ASTM F837/F468) [TABLE 2.2.1-5]
Slotted Close Tolerance 100-deg Flat Countersunk Head Screws (ASTM F837/F468) [TABLE 2.2.1-5]
51 開槽82°沉頭清根機械螺釘 (ASTM F837/F468) [TABLE 2.2.3-1] [美标]
ASME B 18.6.3 (H3A) - 2024		 開槽82°沉頭清根機械螺釘 (ASTM F837/F468) [TABLE 2.2.3-1]
Slotted Undercut 82-deg Flat Countersunk Head machine Screws (ASTM F837/F468) [TABLE 2.2.3-1]
52 100°沉頭開槽機械螺釘 [Table 3] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T3) - 2013		 100°沉頭開槽機械螺釘 [Table 3] (ASTM F837 / F468)
Dimensions of Slotted 100-deg Flat Countersunk Head Screws [Table 3] (ASTM F837 / F468)
53 開槽精密100°沉頭機械螺釘 [Table 5] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T5) - 2013		 開槽精密100°沉頭機械螺釘 [Table 5] (ASTM F837 / F468)
Dimensions of Slotted Close Tolerance 100-deg Flat Countersunk Head Screws (Machine Screws Only) (ASTM F837 / F468)
54 開槽82°沉頭清根機械螺釘 [ Table 9 ] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T9) - 2013		 開槽82°沉頭清根機械螺釘 [ Table 9 ] (ASTM F837 / F468)
Slotted Undercut 82-deg Flat Countersunk Head machine Screws (ASTM F837 / F468)
55 開槽沉頭螺栓 [航天]
QJ 2370 - 1992		 開槽沉頭螺栓
Slotted countersunk head screws
56 開槽沉頭螺釘 [航天]
QJ 2373 - 1992		 開槽沉頭螺釘
Slotted countersunk head screws
57 100°開槽沉頭螺釘 [航空]
HB 7187~7195 - 1995		 100°開槽沉頭螺釘
100° Countersunk Head Bolts
58 100°開槽沉頭螺釘 [航空]
HB 7208~7216 - 1995		 100°開槽沉頭螺釘
Slotted 100 deg flat countersunk head screws
© 易緊通 服務熱線：4006-164580（免長途費）