會員中心 | English | 簡體中文

方槽82°沉頭清根 AB ABR自攻螺釘 ASME B 18.6.3 (H3B-III+T1A) - 2024

選擇規格尺寸點擊↓

10#

12#

1/4

5/16

3/8

ASME B 18.6.3 (H3B-III+T1A) - 2024 方槽82°沉頭清根 AB ABR自攻螺釘

尺寸單位: inch

美标ASME B18.6.3 (H3B-III+T1A) - 2024 ASME 方槽82°沉頭清根 AB ABR自攻螺釘

掃一掃分享

公差

螺紋尺寸
d

10#

12#

1/4

5/16

3/8

d	公稱
PP
槽号
M	參考值
P	最大值
	最小值
d_k	最大值
	最小值
k	最大值
	最小值
α	最大值
	最小值
L₀ ^⑥	公稱
Y ^⑥	螺紋過渡長度(全螺紋)	最大值
b ^⑥	螺紋長度 (長螺釘)	最小值

0.0990	0.1120	0.1250	0.1380	0.1510	0.1640	0.1900	0.2160	0.2500	0.3125	0.3750
28	24	20	20	19	18	16	14	14	12	12
00	00	0	1S	1S	2S	2S	3S	3S	4R	4R
0.050	0.050	0.070	0.091	0.091	0.112	0.112	0.133	0.133	0.191	0.191
0.033	0.033	0.038	0.027	0.027	0.037	0.037	0.073	0.080	0.100	0.100
0.028	0.028	0.028	0.017	0.017	0.027	0.027	0.063	0.065	0.085	0.085
0.187	0.212	0.237	0.262	0.287	0.312	0.362	0.412	0.477	0.597	0.717
0.167	0.191	0.215	0.238	0.262	0.285	0.333	0.380	0.442	0.556	0.670
0.042	0.047	0.053	0.059	0.064	0.070	0.081	0.092	0.107	0.134	0.161
0.033	0.038	0.043	0.048	0.053	0.058	0.068	0.078	0.092	0.116	0.140
82°	82°	82°	82°	82°	82°	82°	82°	82°	82°	82°
80°	80°	80°	80°	80°	80°	80°	80°	80°	80°	80°
3/4	13/16	15/16	1	1-1/8	1-1/4	1-3/8	1-5/8	1-13/16	1-13/16	1-7/8
0.036	0.042	0.050	0.050	0.053	0.056	0.062	0.071	0.071	0.083	0.083
0.590	0.670	0.750	0.830	0.910	0.980	1.140	1.300	1.500	1.500	1.500

①,若以小數規定公稱直徑，應省略小數前和小數點後第四位的零。
②,方槽内壁略帶錐度，以保證插入深量規與有鍍層螺釘凹槽的配合。為使插入深測量深度适用于有塗鍍層的螺釘，制造者在生產（镦頭）時，應為其留出必要的加工餘量。
③,表中的“R”表示正常插入深入。“S”表示短（淺）插入深度。
④,螺釘末端釘尖上不允許因螺紋輾壓而形成的虛尖，允許略帶圓弧或圓鈍形末端。
⑤,小于等于8#的螺釘，螺紋牙頂平面寬度不應超過0.004in，大于8#的應不超過0.006in。
⑥,正常情況下，當螺釘長度小于等于其公稱長度L0時應采用全螺紋，過渡螺紋長度應小于等于Y；若螺釘長度大于其公稱長度L0可采用半牙型式，但其螺紋長度應不小于b。

替代列表

ASME B 18.6.3T10-III+T40 - 2013 ASME B 18.6.3H3B-III+T1A - 2024

長度公差

　　Tapping screws can be made to any length, but they are generally produced in fractional length increments of 1/16 in. for screws up to 1/2 in. long, 1/8 in. for screws over 1/2 in. through 1-1/2 in. long, 1/4 in. for screws over 1-1/2 in. through 3 in. long, and 1/2 in. for screws over 3 in. long.

類型	标稱螺釘長度	長度公差
A、AB、BP	≤1	±0.03
A、AB、BP	＞1	±0.05
B、BF、BT、C、D、F、G、T、TRS	≤3/4	-0.03
	＞3/4,≤1-1/2	-0.05
	＞1-1/2	-0.06

引用參考

鍍鋅、鍍鎳、鍍镉、複合鍍等層鍍層鹽霧腐蝕的防護性能

GB /T 193 - 2003

普通螺紋（一般用途米制螺紋）- 直徑與螺距系列 (ISO 261: 1998, MOD)

GB /T 5280 - 2002

自攻螺釘用螺紋

注：技術數據僅供參考，請以官方原件為準！

類似标準及供貨信息

1	[國際] ISO 5835 (F1) - 1991	内六角接骨螺釘 (HA型) [Figure 1] Screw With Shallow Thread (HA) [Figure 1]
2	[國際] ISO 5835 (F3) - 1991	内六角接骨螺釘 (HB型) [Figure 3] Screw With Deep Thread (HB) [Figure 3]
3	[萬禧] WS 9200 - 2014	内六角圓柱頭自攻螺釘 Hexagon socket cheese head self-tapping screws
4	[美标] ASME B 18.6.5M (T11) - 2000	米制四方槽沉頭自攻釘 [Table 11] Metric square recessed flat countersunk tapping screws [Table 11] 供應商(2)
5	[美标] ASME B 18.6.5M (T11) - 2000 (R2010)	米制四方槽沉頭自攻釘 [Table 11] Metric Type Ill Square-Recessed Flat Countersunk Head Tapping Screws [Table 11] 供應商(2)
6	[美标] ASME B 18.6.3 (H1B-III+T1A) - 2024	四方槽沉頭螺釘 (ASTM F837, F468) Square Recessed Countersunk Head Screws (ASTM F837, F468)
7	[美标] ASME B 18.6.3 (H2B-III+T1A) - 2024	四方槽半沉頭 AB ABR自攻螺釘 Square recessed raised countersunk head tapping screws - Type AB and ABR
8	[美标] ASME B 18.6.3 (H3D-III+T1A) - 2024	四方槽82°半沉頭清根 AB ABR自攻螺釘 Square recessed undercut oval countersunk head tapping screws - Type AB and ABR
9	[美标] ASME B 18.6.3 (H5C-III+T1A) - 2024	四方槽盤頭 AB ABR自攻螺釘 Square Recessed Pan Head Tapping Screws - Type AB and ABR
10	[美标] ASME B 18.6.3 (H6B-III+T1A) - 2024	十字槽球面圓柱頭 AB ABR自攻螺釘 Cross recessed raised cheese head tapping screws - Type AB and ABR
11	[美标] ASME B 18.6.3 (H7B-III+T1A) - 2024	四方槽大扁頭 AB ABR自攻螺釘 Square Recessed Mushroom Head Tapping Screws - Type AB and ABR
12	[美标] ASME B 18.6.3 (H11B-III+T1A) - 2024	方槽圓頭 AB ABR自攻螺釘 Square Recessed Round Head Tapping Screws - Type AB and ABR
13	[美标] ASME B 18.6.3 (T2-III+T40) - 2013	方槽82度沉頭AB ABR自攻螺釘 82° Square Recessed Countersunk Head Tapping Screws - Type AB (ABR)
14	[美标] ASME B 18.6.3 (T10-III+T40) - 2013	方槽82°沉頭清根 AB ABR自攻螺釘 Undercut 82-deg Square Recessed Countersunk Head Tapping Screws - Type AB (ABR)
15	[美标] ASME B 18.6.3 (T8-III+T40) - 2013	四方槽半沉頭 AB ABR自攻螺釘 Square recessed raised countersunk head tapping screws - Type AB and ABR
16	[美标] ASME B 18.6.3 (T12-III+T40) - 2013	四方槽82°半沉頭清根 AB ABR自攻螺釘 Square recessed undercut oval countersunk head tapping screws - Type AB and ABR
17	[美标] ASME B 18.6.3 (T19-III+T40) - 2013	四方槽盤頭 AB ABR自攻螺釘 Square Recessed Pan Head Tapping Screws - Type AB and ABR
18	[美标] ASME B 18.6.3 (T22-III+T40) - 2013	四方槽球面圓柱頭 AB ABR自攻螺釘 Square Recessed Raised Cheese Head Tapping Screws - Type AB and ABR
19	[美标] ASME B 18.6.3 (T25-III+T40) - 2013	四方槽大扁頭 AB ABR自攻螺釘 Square Recessed Mushroom Head Tapping Screws - Type AB and ABR
20	[美标] ASME B 18.6.3 (T36-III+T40) - 2013	方槽圓頭 AB ABR自攻螺釘 Square Recessed Round Head Tapping Screws - Type AB and ABR
21	[美标] ASME B 18.6.5M (T19) - 2000	米制四方槽盤頭自攻螺釘 [Table 19] Metric square slot pan head tapping screws [Table 19]
22	[美标] ASME B 18.6.5M (T15) - 2000 (R2010)	米制四方槽半沉頭自攻釘 [Table 15] Metric Type III square-recessed oval countersunk head tapping screws
23	[美标] ASME B 18.6.5M (T19) - 2000 (R2010)	米制四方槽盤頭自攻螺釘 [Table 19] Metric Type Ill Square-Recessed Pan Head Tapping Screws [Table 19]
24	[醫藥行業标準] YY 0018 (T1) - 2016	HA型内六角接骨螺釘 [Table 1] Screw With Shallow Thread (HA) [Table 1]
25	[醫藥行業标準] YY 0018 (T4) - 2016	HB型内六角接骨螺釘 [Table 4] Screw With Deep Thread (HB) [Table 4]