牌号 | X5CrNiMo 17-12-2 |
---|---|
德国W-Nr. | 1.4401 |
对应标准 | DIN EN 10269-2014
规定高温和/或低温性能的紧固件用钢和镍合金 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
归类 | 奥氏体不锈钢 |
性能 | 耐腐蚀 |
标签 | A4 |
说明 | ①实例应用: 是制造DIN 7964 - 1990 粗牙缩径杆(细杆)螺栓、螺钉的材料之一,此螺栓螺钉性能等级A4-50(M20及以下规格)、A4-70(M20以上规格),参考标准ISO 3506-1对材料的相关规定 —本欧洲标准规定了非合金和合金(包括不锈钢)钢和镍合金制成的在高温和/或低温下具有指定性能的紧固件的半成品、棒材的要求。 —本标准的要求也适用于成品紧固件 —EN 10021中的一般交货技术条件也适用于按照本标准提供的产品。 |
密度 | 8 g/cm3 |
-
交付条件下在高温下的最小屈服强度
Material designation Heat treatment condition Diameter
d
mm
Minimum 0.2%-proof strength Rp0.2 in MPa at a temperature (in°C) of: Name Number 50 100 150 200 250 300 350 400 450 500 550 600 650 X5CrNiMo 17-12-2 1.4401 +AT d≤160 191 175 158 145 135 127 120 115 112 110 108 - - -
交付条件下在高温下的最小抗拉强度
Material designation Heat treatment condition Diameter
d
mm
Minimum tensile strength Rm in MPa at a temperature (in°C) of: Name Number 50 100 150 200 250 300 350 400 450 500 550 600 650 X5CrNiMo 17-12-2 1.4401 +AT d≤160 480 460 440 420 415 410 410 410 405 390 375 350 - -
在交付条件下的最小冲击吸收能量(纵向)
Material designation Heat treatment condition Diameter
d
mm
Minimum impact energy KV2inJ(ISO-V test piece) at a test temperature in°C of: Name Number -270 -196 -160 -140 -120 -110 -100 -90 -80 -70 -60 -50 -40 -20 0 +20 X5CrNiMo17-12-2 1.4401 +C700 d≤35 - 50 - - - - - - - - - - - - - 80 -
符合本欧洲标准的产品热处理指南
Material designation Heat-treatment symbol Normalizing,quenching or solution annealing temperature °C Type of cooling Tempering or precipitation treatment (and time)°C Name Number X5CrNiMo17-12-2 1.4401 +AT 1020 to 1120 a,w - a-air w-water
-
物理性能
n.a.-no values available各温度°C时静态弹性模量 20°C与各温度间热膨胀系数 热导率 比热容 电阻率 20 100 200 300 400 500 600 700 800 100°C 200°C 300°C 400°C 500°C 600°C 20°C 20°C 20°C GPa 10-6 K-1 W/m.K J/kg.K Ω.mm2/m 200 194 186 179 172 165 - - - 16 16.5 17 17.5 18 n.a. 15 500 0.75
注:数据仅供参考!如有疑问,请填写"我要纠错"!